How to set 1 deco connect to preferred One

If your facing problems like drop in signal, speed drop or Wi-Fi bouncing between deco units, then its time to fix your main Deco device. Its easy to configure if you know exactly what to do. Just a few small steps and your home network will start working again. You don’t have to have a technical background to set 1 deco connect to preferred one. Before we start, remember that Deco units work together in a mesh setup. It means all units share the same network, i.e. one unit connects to the main network and all other units connect to that particular unit.

Lets take a look on the essential steps

Step 1: Check What’s Connected Where

First, open the Deco app. You’ll see a map or list of your Deco units. Each one shows what devices are linked to it. Scroll through and find your device — your phone, laptop, or TV.

If it’s connected to the wrong Deco, that’s fine. You just need to set 1 Deco connect to preferred one.

Here’s the quick check: tap on the device name, and it’ll show which Deco node it’s on. Look at the signal strength. If it’s low or unstable, you’ve found your issue.

At this point, do nothing fancy. Just unplug the Deco you don’t want your device to use for a minute. Your device will automatically switch to another Deco. Plug the old one back in after. That forces a recheck. Sometimes that alone fixes it.

Step 2: Find the Right Spot

Now comes the part most people skip – positioning. Mesh systems depend a lot on placement. If you want to set 1 Deco connect to preferred one, both the device and the Deco must be in line of sight, or at least close enough.

• Move your device near the preferred Deco. Wait a bit. Wi-Fi networks take a few seconds to adjust. You can also switch your device’s Wi-Fi off and on again. That usually helps it latch onto the nearest Deco.
• In the Deco app, refresh the screen. You should now see that your phone or laptop is showing under the Deco you want.
• This step sounds too basic, but it works for most people. Placement and signal overlap cause half the problems.

Step 3: Use the App Controls

If the simple tricks don’t stick, you can manually tweak it through the Deco app. Not all versions have the same options, but here’s the general idea.

Go to the connected device list. Tap the one you want to manage. You might see an option like “Preferred Deco” or “Signal Source.” At last select that unit, that you want as main connector

If you don’t see that option, don’t worry. Some models don’t support it directly. In that case, the trick is to block the device temporarily from other Decos. That sounds odd, but it’s how you set 1 Deco connect to preferred one manually without an official button.

Just unplug all other Decos with the help of the app, continue the same process until your device connects to the correct one. Once that’s done, reconnect the others. Your device usually remembers the last good connection and prefers it next time.

Step 4: Assign Static IP or Band

Some advanced users go a little deeper. If your Deco supports it, you can assign a fixed IP or choose the Wi-Fi band (2.4GHz or 5GHz). That helps when you set 1 Deco connect to preferred one and want your device to stay steady.

Here’s what you do:

• Go to your Deco app → Device settings → Network details. Assign a static IP (optional). Then, check if you can set the band manually.
• For example, 2.4GHz goes farther but slower, while 5GHz is faster but has less range. If the preferred Deco is near your device, lock it to 5GHz. That usually makes the connection stick to that unit.
• Not every Deco model allows full control, but try it if you can. It’s not risky. You can always switch back.

Step 5: Restart Everything in Sequence

If things still don’t behave, it’s time for a full restart cycle. Turn off your main router and all Deco units. Wait about a minute. Then power on only the main Deco first. Let it come online. Then plug in the preferred one next.

When the LEDs go stable, turn on the rest, this order helps the mesh re-sync properly. Once the network is up, connect your device near the Deco you want to keep as preferred.

You’ll likely see that your phone, tablet, or PC now connects straight to that one. That’s how you set 1 Deco connect to preferred one through proper network reset — not fancy, just practical.

Step 6: Rename or Label for Clarity

Name your devices uniquely, so that you can differentiate them. This will not only reduce confusion but also let you know where you can connect your device.

When you set 1 Deco connect to preferred one, these labels help you track which one’s performing better. You can see signal strength and connected devices easily.

A simple name tag avoids confusion, especially when troubleshooting later. Don’t skip this. It saves you time in the long run.

Common Mistakes People Make

Some folks keep moving the Deco units around too much. Don’t do that unless you really need to. The mesh system learns your home layout and adjusts. Every time you move them, it has to relearn.

Others forget to update the firmware. If you’re struggling to set 1 Deco connect to preferred one and it keeps resetting, check for updates in the app. Firmware bugs often mess with connection logic.

And avoid using third-party Wi-Fi extenders with Deco. It confuses the mesh and breaks the logic of “preferred” connection. Stick with the Deco system itself.

Wrapping Up

Just remember to start simple, if the Deco is not working, unplug it, move it closer to the router and plug it again. The goal is to make your device stick to the strongest and most stable Deco in your space. Once you set 1 Deco connect to preferred one, your wifi stops bouncing around and you’ll notice fewer dropouts.

Mesh networks are smart and are capable to manage most task on their own, but manual control cannot be excluded completely. Just follow the steps given in this guide & your Deco connection will run smooth.